How to repair an office chair, if it falls?

Not only in the office, in almost every home there is a computer chair. It is comfortable to sit at the computer. But chairs often fail, because we use them every day. It happens that some serve for many years, while others become useless in just a few months. Lifetime depends primarily on how hard you treat it. Weight category plays an important role. This piece of furniture provides weight up to 120 kg.

It happens that some chairs serve for many years, while others become useless in just a few months.

Thus, the air ceases to flow from the first chamber to the second.

If you are replacing the gas lift during the cold season, do not use it immediately.

Such chairs consist of mechanical parts and hydraulic. If at the moment when you sit down, the chair falls, then, most likely, gas escaped from the gas cartridge. It turns into a big problem and interferes with work. It is unrealistic to do business when sitting in a chair uncomfortable. This can result in spinal problems. It is possible that back pain will occur or scoliosis will develop. That is why it is important that the chair was in order.

Weight category plays an important role.

On the floor you need to put something, such as a newspaper, so as not to get dirty.

It is necessary to make sure that the piastre and swing mechanism are properly sealed, that the lever could be bent.

It is better not to repair it on your own, as it represents a threat to health, and maybe life. It is better to buy a new gas cartridge. It is not so expensive. If you are masterful enough, you can easily make a replacement yourself. All that is needed for repair can be purchased at the outlet where such chairs are sold. Of course, home repair will significantly save your home budget. You doubt that you will cope with this work, it is better, of course, to turn to specialists. It is not necessary to take the chair to the address where the repair is carried out, as many experts go to the house.

Such chairs consist of mechanical parts and hydraulic.

Actually, skillful people will not be difficult to repair the chair yourself.

It is important to do everything carefully and do not rush, then the chair will last a long time.

Chairs often fail, because we use them every day.

List of required materials and tools

It is better not to repair it on your own, as it represents a threat to health, and maybe life.

This piece of furniture provides weight up to 120 kg.

If at the moment when you sit down, the chair falls, then, most likely, gas escapes from the gas cartridge

Repair process: step by step instructions

Often in such chairs gas-lift comes into disrepair. This mechanism has two cameras, there is air in them. He is driven by a lever, he presses the valve. Thus, the air ceases to flow from the first chamber to the second. Therefore, the height of the chair can be adjusted.

It is better to buy a new gas cartridge.

It is unrealistic to do business when sitting in a chair uncomfortable.

That is why it is important that the chair was in order.

Before starting work, you must wear goggles; cylinder or lubricant particles may get into your eyes. If you are replacing the gas lift during the cold season, do not use it immediately. It is better to leave to warm at room temperature for a day. On the floor you need to put something, such as a newspaper, so as not to get dirty.

1. First, using the figure screwdriver unscrew the harnesses from the swing mechanism. After you have turned the chair over, you need to mark the front side of the mechanism, then unscrew the four bolts and separate the frame from the seat.
2. Now you need to disassemble the gas lift. We take the hammer and lightly begin to strike the swing mechanism at the base of the gas lift from the cross. It is important not to bend the mechanism. If it was not possible to knock it down, it is necessary to squeeze the gas lift base with a vice and roll the swing mechanism.
3. Now it is necessary to separate the gas cartridge from the cross. To do this, you need a metal drift. Using it, you will avoid unnecessary damage. To facilitate the work, sprinkle with WD40 grease on the bottom and on the upper side of the cross. It is necessary to turn the cross with rollers up and with gentle movements to knock the gas cartridge out of the conical base. It is better to carry out this work with an assistant; it is inconvenient for one person to do this.
4. We change the gas cartridge which has become useless for a new one. Insert it, making an effort in the hole of the cross. Make sure that the gas cartridge fits in diameter to the crosspiece. The casing on the gas lift is put on before you connect it to the seat.
5. Attach the swing mechanism to the seat with four bolts. It is important to ensure that the front sides of the mechanism and the seat match. Turn over the seat and put on the gas lift on the swing mechanism. Now we insert the gas-lift into the mechanism and with an emphasis we press. Check whether everything is done correctly. We sit on the chair and see how the gas lift works.

All that is needed for repair can be purchased at the outlet where such chairs are sold.

If you are masterful enough, you can easily make a replacement yourself.

You doubt that you will cope with this work, it is better, of course, to turn to specialists.

You completed the repair of the chair, collected it, but the difficulties with the gas cartridge remained? It may have turned out to be of poor quality. Before returning to the store, you need to check whether the lever of the gas cartridge keeps the lever from the swing mechanism. It is necessary to make sure that the piastre and swing mechanism are properly sealed, that the lever could be bent. If everything is in order, you need to replace the gas lift.

It is not necessary to take the chair to the address where the repair is carried out, as many experts go to the house.

Before starting work, you must wear goggles; cylinder or lubricant particles may get into your eyes.

It is important not to bend the mechanism.

Actually, skillful people will not be difficult to repair the chair yourself. It is important to do everything carefully and do not rush, then the chair will last a long time.

Often in such chairs gas-lift comes into disrepair.

To facilitate the work, sprinkle with WD40 grease on the bottom and on the upper side of the cross.

It is better to carry out this work with an assistant; it is inconvenient for one person to do this.

VIDEO: Broken office chair? Repair on the cheap